臺灣安頌ANSON葉片泵臺灣安頌ANSON油泵臺灣安頌ANSON江蘇代理
臺灣安頌ANSON定量葉片泵IVPQ系列
IVPQ2-10-F-R IVPQ2-12-F-R IVPQ2-14-F-R IVPQ2-15-F-R
IVPQ2-17-F-R IVPQ2-19-F-R IVPQ2-21-F-R IVPQ2-25-F-R


IVPQ2-10-F-R-1A-10 IVPQ2-12-F-R-1A-10
IVPQ2-14-F-R-1A-10 IVPQ2-15-F-R-1A-10
IVPQ2-17-F-R-1A-10 IVPQ2-19-F-R-1A-10
IVPQ2-21-F-R-1A-10 IVPQ2-25-F-R-1A-10


IVPQ2-10-F-R-1B-10 IVPQ2-12-F-R-1B-10
IVPQ2-14-F-R-1B-10 IVPQ2-15-F-R-1B-10
IVPQ2-17-F-R-1B-10 IVPQ2-19-F-R-1B-10
IVPQ2-21-F-R-1B-10 IVPQ2-25-F-R-1B-10


IVPQ2-10-F-R-1C-10 IVPQ2-12-F-R-1C-10
IVPQ2-14-F-R-1C-10 IVPQ2-15-F-R-1C-10
IVPQ2-17-F-R-1C-10 IVPQ2-19-F-R-1C-10
IVPQ2-21-F-R-1C-10 IVPQ2-25-F-R-1C-10


IVPQ2-10-F-R-1D-10 IVPQ2-12-F-R-1D-10
IVPQ2-14-F-R-1D-10 IVPQ2-15-F-R-1D-10
IVPQ2-17-F-R-1D-10 IVPQ2-19-F-R-1D-10
IVPQ2-21-F-R-1D-10 IVPQ2-25-F-R-1D-10

泵的噪聲過大。泵的噪聲過大的原因及排除方法見表1-8。表1-8泵的噪聲過大的原因及排除方法常見故障及其原因排除方法濾油器堵塞，吸油不暢淸洗吸入端漏氣用涂黃油的方法，逐個檢査吸油管接頭處，若噪聲減少應緊固接頭。或直接觀察回油口處是否出現氣泡。泵端密封磨損在軸端油封處涂上黃油，若噪聲減小，應更換油封泵蓋螺釘由于振動而松動將螺釘連接處涂上黃油，若噪聲小，應緊固螺釘泵與電動機軸不同心重新調整使之同心轉子的葉片槽兩側與其兩端面不垂直更換轉子配油盤卸荷三角槽太短用什錦銼適當修改，使前一葉片過卸荷槽時，后一葉片已脫離吸油腔花鍵槽軸端的密封過緊（有燙手現象）適當調整更換泵的轉速太高按規定轉速使用油泵的吸油量不足檢查油液高度液壓油嚴重污染拆下濾油器，檢查濾油器是否破損，是否有較多固體吸附，更換濾油器和液壓油壓力振擺檢查泵芯總壓閥閥芯磨損情況